Email updates

Keep up to date with the latest news and content from Biotechnology for Biofuels and BioMed Central.

Open Access Research

Biohydrogen production from arabinose and glucose using extreme thermophilic anaerobic mixed cultures

Angela A Abreu12, Dimitar Karakashev2, Irini Angelidaki2, Diana Z Sousa1 and M Madalena Alves1*

Author Affiliations

1 Institute for Biotechnology and Bioengineering, Centre of Biological Engineering, University of Minho, 4710-057 Braga, Portugal

2 Department of Environmental Engineering, Technical University of Denmark, Bygningstorvet 115, DK-2800, Kgs Lyngby, Denmark

For all author emails, please log on.

Biotechnology for Biofuels 2012, 5:6  doi:10.1186/1754-6834-5-6


The electronic version of this article is the complete one and can be found online at: http://www.biotechnologyforbiofuels.com/content/5/1/6


Received:6 July 2011
Accepted:13 February 2012
Published:13 February 2012

© 2012 Abreu et al; licensee BioMed Central Ltd.

This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract

Background

Second generation hydrogen fermentation technologies using organic agricultural and forestry wastes are emerging. The efficient microbial fermentation of hexoses and pentoses resulting from the pretreatment of lingocellulosic materials is essential for the success of these processes.

Results

Conversion of arabinose and glucose to hydrogen, by extreme thermophilic, anaerobic, mixed cultures was studied in continuous (70°C, pH 5.5) and batch (70°C, pH 5.5 and pH 7) assays. Two expanded granular sludge bed (EGSB) reactors, Rarab and Rgluc, were continuously fed with arabinose and glucose, respectively. No significant differences in reactor performance were observed for arabinose and glucose organic loading rates (OLR) ranging from 4.3 to 7.1 kgCOD m-3 d-1. However, for an OLR of 14.2 kgCOD m-3 d-1, hydrogen production rate and hydrogen yield were higher in Rarab than in Rgluc (average hydrogen production rate of 3.2 and 2.0 LH2 L-1 d-1 and hydrogen yield of 1.10 and 0.75 molH2 mol-1substrate for Rarab and Rgluc, respectively). Lower hydrogen production in Rgluc was associated with higher lactate production. Denaturing gradient gel electrophoresis (DGGE) results revealed no significant difference on the bacterial community composition between operational periods and between the reactors. Increased hydrogen production was observed in batch experiments when hydrogen partial pressure was kept low, both with arabinose and glucose as substrate. Sugars were completely consumed and hydrogen production stimulated (62% higher) when pH 7 was used instead of pH 5.5.

Conclusions

Continuous hydrogen production rate from arabinose was significantly higher than from glucose, when higher organic loading rate was used. The effect of hydrogen partial pressure on hydrogen production from glucose in batch mode was related to the extent of sugar utilization and not to the efficiency of substrate conversion to hydrogen. Furthermore, at pH 7.0, sugars uptake, hydrogen production and yield were higher than at pH 5.5, with both arabinose and glucose as substrates.

Keywords:
biohydrogen; extreme thermophilic conditions; arabinose; hydrogen partial pressure; pH; lactate

Background

Hydrogen is a promising renewable energy carrier that can contribute towards a low carbon economy. Fermentative hydrogen production from carbohydrate-containing feedstock, such as glucose, sucrose and starch, has been extensively studied [1,2]. However, second generation hydrogen fermentation technologies are presently emerging as promising and more cost-effective solutions [1,3].

Lignocellulosic material must be pre-treated prior to fermentation to hydrogen in order to remove lignin and hemicelluloses, reduce the cellulose crystallinity and increase the surface area of the material to enhance the release of sugars [4]. Physico-chemical pre-treatment of lignocellulosic material, such as the application of acid, alkaline or oxidative conditions at ambient or elevated temperatures, yields a mixture of pentoses and hexoses [1]. Efficient microbial fermentation of hexoses and pentoses is, therefore, the key step for hydrogen production from plant biomass. However, combined fermentation of mixtures of hexoses and pentoses is often prevented due to catabolic repression; in the presence of glucose, pentoses might be converted to a lesser extent thereby decreasing overall fermentation yields [5,6]. Moreover, efficient hydrogen production from sugars is dependent on the different possible fermentation pathways (Figure 1).

thumbnailFigure 1. Major metabolic pathways for glucose and arabinose fermentation in mixed cultures (adapted from [7,8]).

Most of the extreme thermophiles from the phylum Clostridia use the Embden-Meyerhof pathway to metabolize hexose sugars to pyruvate [9]. Biohydrogen can be then formed via decarboxylation of pyruvate to acetyl CoA, in which reduced ferredoxin (Fdred) is generated and acts as a direct electron donor for proton reduction to hydrogen (Figure 1). Maximum hydrogen yield, both from hexoses or pentoses, is obtained with acetate as the fermentation product (equations 1 and 2). Low yields are associated with the formation of more reduced end products compared to acetate, such as butyrate, propionate and alcohols (ethanol, butanol) and lactic acid.

<a onClick="popup('http://www.biotechnologyforbiofuels.com/content/5/1/6/mathml/M1','MathML',630,470);return false;" target="_blank" href="http://www.biotechnologyforbiofuels.com/content/5/1/6/mathml/M1">View MathML</a>

(1)

<a onClick="popup('http://www.biotechnologyforbiofuels.com/content/5/1/6/mathml/M2','MathML',630,470);return false;" target="_blank" href="http://www.biotechnologyforbiofuels.com/content/5/1/6/mathml/M2">View MathML</a>

(2)

Environmental parameters such as pH, hydrogen partial pressure and temperature have been documented as key factors in hydrogen fermentation [10]. The pH of the medium is known to regulate the shift to solventogenesis during the fermentation of sugars [7]; the effect of low pH in the inhibition of methanogenic archaea is also recognized and could be potentially used as a selective pressure in mixed culture systems. Metabolic pathways of hydrogen formation are sensitive to hydrogen partial pressure (PH2) and are subject to end-product inhibition [11,12]. In addition, fermentation processes operating under thermophilic (45 to 60°C) and extreme thermophilic (65 to 80°C) could possibly result in higher hydrogen yields due to favorable thermodynamics and lower variety in soluble by-products [13]. High temperatures inhibit the growth of methanogenic archaea and homoacetogenic bacteria [13]; this is an important advantage when using mixed-cultures for hydrogen production because it prevents consumption of hydrogen by these microbial groups (as is often the case in mesophilic fermentation). Also, higher hydrolysis rates of cellulosic material have been observed in studies performed under thermophilic conditions, with the concurrent formation of higher amounts of fermentable sugars [14]. Hydrogen production by mixed culture fermentation is more suited for industrial applications, when compared to pure culture fermentation. Some of the advantages are: (i) no need for sterile cultivation, (ii) presence of high microbial diversity, which offers increased adaptation capacity, (iii) possibility of mixed substrates co-fermentation, and (iv) higher capacity for continuous processing [15,16]. However, and although there is a considerable number of studies on H2 production at extreme thermophilic conditions using pure cultures, studies using mixed-cultures are lacking [17,18]. Also, the effect of pH and hydrogen partial pressure has been described in several pure cultures of thermophiles and extreme-thermophiles but the effect in mixed cultures is not yet clear [17].

In the present study, the conversion of a C5-sugar (arabinose) and a C6-sugar (glucose) to hydrogen, using anaerobic mixed-cultures under extreme thermophilic conditions (70°C), was studied in continuous expanded granular sludge bed (EGSB) reactors. Microbial diversity in arabinose- and glucose-fed bioreactors was assessed using a PCR-DGGE (denaturing gradient gel electrophoresis) approach. Additional batch experiments were performed with extreme-thermophilic mixed cultures to study the effect of hydrogen partial pressure and pH on hydrogen production from arabinose and glucose.

Results

EGSB reactors performance

Hydrogen production rates in arabinose- and glucose-fed reactors (Rarab and Rgluc) are shown in Figures 2 and 3, respectively. Only H2 and CO2 were detected in the gas phase; methane was not produced during all operation time. During start-up (period I), hydrogen production rates of approximately 0.3 L H2 L-1d-1 were observed in both reactors. This corresponds to hydrogen yields of roughly 0.2 and 0.3 mol H2 per mol of substrate consumed, for Rarab and Rgluc respectively (Table 1). In period II, the increase in arabinose and glucose inlet concentration to 16.6 mM and 13.8 mM, respectively, resulted in hydrogen yields of about 0.80 mol H2 per mole of substrate in both Rarab and Rgluc (Table 1). Maximum hydrogen production rates in period II were of 1.36 ± 0.04 and 1.12 ± 0.07 LH2 L-1 d-1 in Rarab and Rgluc, respectively. Substrate was completely consumed in both reactors and the main by-products formed were butyrate, acetate and lactate (Figures 2 and 3). In operation period III, substrate concentrations fed to Rarab and Rgluc were increased to 33.3 mM of arabinose and 27.7 mM of glucose, respectively. As a result of this increase, there was a temporary raise in arabinose/glucose concentration in the effluent but, after 13 days of acclimation to the higher substrate loads, virtually all glucose and an average of 79% arabinose were used in the reactors (Table 1) Steady state hydrogen production rates of 3.26 ± 0.16 and 2.06 ± 0.06 L H2 L-1 d-1 were observed in Rarab and Rgluc, respectively (Figures 2 and 3). During period III, Rgluc showed a stable hydrogen yield of about 0.75 mol H2 per mole of substrate consumed. Hydrogen yield in Rarab was significantly higher, that is. 1.10 mol H2 per mole of substrate consumed. Lactate concentration in Rgluc increased sharply during period III of operation reaching values of approximately 20 mM (Figure 3). An increase in lactate concentration was also observed in Rarab, but did not exceed 11 mM (Figure 2). Estimation of the theoretical reduced form of nicotinamide adenine dinucleotide (NADH) production from glucose and arabinose, considering the main catabolic pathways (that is, Embden-Meyerhof for glucose and a combination of pentose phosphate and Embden-Meyerhof pathways for arabinose (Figure 1)), demonstrates that a higher reducing power was potentially formed in Rgluc than in Rarab. Estimated NADH concentration in Rgluc was 42 mM after three days of operation, while in Rarab was 37 mM after five days of operation.

thumbnailFigure 2. Effect of OLR on performance of Rarab (a) hydrogen production rate and HRT, (b) soluble fermentation products and residual arabinose.

thumbnailFigure 3. Effect of OLR on performance of Rgluc (a) hydrogen production rate and HRT, (b) soluble fermentation products and residual glucose.

Table 1. Process performance of Rarab, Rgluc and Rgluc+arab.

Bacterial community composition dynamics in EGSB reactors

DGGE profiles generated for sludge samples withdrawn from Rarab and Rgluc (Figure 4) show that bacterial composition in both reactors' sludge at the end of periods II (Day 27) and III (Day 41) are identical. Differences in substrate composition did not affect the bacterial community in reactors Rarab and Rgluc and similarity index between Arab/Gluc samples at the end of the operation was as high as 94%. Predominant DGGE bands in Rgluc and Rarab were identical to the ones present in the inoculum used in this study and for which the phylogeny had been previously assessed [6]. Two of the predominant DGGE bands showed high similarity (> 99%) with the hydrogen-producing Thermoanaerobacterium thermosaccharolyticum. Members of the Klebsiella, Bacillus and Sporolactobacillus genera, detected in the inoculum sludge, were also predominant in Rgluc and Rarab.

thumbnailFigure 4. DGGE profile of granular sludge samples from a reactor fed with arabinose and glucose [6]and at Day 27 and Day 41 from arabinose (and glucose reactors.

Effect of hydrogen partial pressure and pH on batch hydrogen production from arabinose and glucose

The effect of the hydrogen partial pressure, while using arabinose and glucose as substrates, was studied in batch experiments at pH 5.5 (equivalent to pH 5.0 at 70°C). Assays were performed allowing the accumulation of hydrogen in the headspace (no headspace flushing, NHF), or preventing hydrogen accumulation in the headspace (headspace flushing, HF). Subsequently, HF assays were performed at pH 7.0 (that is, pH 6.5 at 70°C) to study the effect of pH increase in hydrogen production. Substrates were added at the beginning of the experiment and a second addition was performed after complete depletion of the first load.

In the NHF (pH 5.5), maximum hydrogen concentration in the gas was achieved 44 and 20 h after the second addition of arabinose or glucose addition, respectively (Figure 5a, b). At this point, hydrogen partial pressure in both arabinose and glucose assays was roughly 1.2 × 104 Pa (at 70°C), which corresponds to a dissolved hydrogen concentration of 105 μM. From this point on, hydrogen production was not significant, even though only 35% of arabinose and 13% of glucose were present at the end of the experiment. Identical hydrogen yield, that is, 0.7 mol H2 per mole of substrate, was obtained for NHF arabinose and glucose experiments (Table 2).

thumbnailFigure 5. Time course of hydrogen production and substrate consumption, O PiH2 ; ■ arabinose; x glucose. a, b) pH 5.5 without headspace flushing. c, d) pH 5.5 with headspace flushing. e, f) pH 7 with headspace flushing.

Table 2. Substrate consumption and hydrogen yields from batchexperiments.

Hydrogen production from arabinose could be increased in assays in which hydrogen partial pressure in the headspace was kept low (HF). A cumulative hydrogen production of 1. To -1.7 × 104 Pa (at 70°C) was attained in HF (pH 5.5) arabinose experiments (Figure 5c). This value is significantly higher than the one obtained in NHF experiments (P< 0.01: t-test), and corresponds to an increase of about 40% in hydrogen pressure. However, the highest increment in hydrogen cumulative production (that is, 62%) was observed in HF arabinose assays performed at pH 7.0 (cumulative hydrogen pressure of 2.8 × 104 Pa at 70°C (Figure 5f)). Arabinose was totally consumed in HF assays at pH 7.0, while a fraction substrate (approximately 1%) was not used in HF assays at pH 5.5 (Figure 5c, e). Nevertheless, non-consumed arabinose in HF at pH 5.5 was considerably lower than in NHF assays (Figure 5a, c). Hydrogen yields in HF arabinose experiments at pH 5.5 and pH 7.0 were 0.76 and 1.15 mol H2 per mole of substrate consumed, respectively (Table 2).

Hydrogen production values in HF and NHF glucose experiments at pH 5.0 were not significantly different. However, cumulative hydrogen production from glucose in HF experiments at pH 7.0 was significantly higher (P < 0.001: t-test) than at pH 5.5 (Figure 5d, f). Hydrogen cumulative pressure in HF glucose assays at pH 7 was of 2.6 × 104 Pa (at 70°C, Figure 5f). Glucose was totally consumed in HF assays both at pH 5.5 and pH 7.0. Hydrogen yields in HF glucose experiments at pH 5.5 and pH 7.0 were 0.6 and 1.4 mol H2 per mole of substrate consumed, respectively (Table 2).

At pH 5.5 approximately 20 mM of ethanol was produced from both substrates. At pH 7 ethanol formation did not exceed 15 mM (Figure 6). Acetate formation from both substrates at pH 7 achieved approximately 14 mM (Figure 6). In the case of glucose a decrease in 40% of lactate formation was also observed in incubations at pH 7.

thumbnailFigure 6. Time course of soluble fermentation products, O ethanol; lactate; + acetate. a, b) pH 5.5 with headspace flushing. c, d) pH 7 with headspace flushing.

Discussion

Continuous hydrogen production in EGSB reactors

Rarab and Rgluc showed similar performance during periods I and II of operation. However, when a higher organic loading rate was applied to the reactors (period III of operation, arabinose and glucose concentrations of 33.3 and 27.7, respectively), Rarab showed a steady state hydrogen production rate 1.6 × higher than Rgluc. Furthermore, hydrogen production rate measured in Rarab was 1.3 × higher than the one reported by Abreu et al. [6] when feeding a EGSB reactor with a mixture of arabinose and glucose (1/1). Hydrogen production yield in Rarab was 1.10 mol H2 per mole of arabinose consumed, which is considerably higher than the yields obtained in Rgluc (0.75 mol H2 per mole of glucose) and Rgluc+arab (0.77 mol H2 per mole glucose + arabinose) (Table 1). According to these results, the presence of glucose may possibly decrease the overall hydrogen yield in continuous operation, particularly when higher organic loading rates are applied. Lower hydrogen production observed in Rgluc was likely associated with high lactate production (Figure 3). According to the Embden-Meyerhof pathway (Figure 1), sugar-derived pyruvate is (1) reduced to lactate, with regeneration of NADH (Table 3, reaction 1), or (2) oxidized to acetyl-CoA, with the production of reduced ferredoxin (Table 3 reaction (2)). Reaction (1) does not yield hydrogen, while in reaction (2) one mol of pyruvate results in the formation of 2 mol hydrogen. However, and considering Gibbs energy variations, reaction (1) seems to be energetically more favorable than reaction (2), especially at higher hydrogen partial pressures (Table 3).

Table 3. Gibbs free energy changes for some of the glucose and arabinose oxidation reactions.

The fact that the microbial communities' composition in the reactors did not change along the three operational periods (Figure 4), suggests that the higher concentration of lactate produced in Rgluc during period III is related to metabolic changes and is not a consequence of bacterial community shifts. Two of the predominant DGGE bands present in the reactors sludge could be affiliated with Thermoanaaerobacterim thermosacharolyticum (similarity higher than 99%). A draft genome of T. thermosacharolyticum (Joint Genome Institute) allowed a search of genes that encode metabolic enzymes involved in pyruvate conversion. A L-lactate dehydrogenase (EC 1.1.1.27) was present indicating the possibility of pyruvate reduction to lactate. Some genes codifying subunits of enzymes related to pyruvate-ferredoxin oxidoreductases and NADH oxidoreductases were also found but a complete picture of the mechanisms involved in pyruvate conversion to acetyl-CoA cannot be retrieved. Clones corresponding to other predominant DGGE bands present in reactors sludge exhibited highest sequence identity with Klebsiella sp. (99%) and Bacillus coagullans (99%). All these microorganisms are able to produce hydrogen and lactate, among other products, from a variety of carbon sources [21-23]. No genomic information is available for these species and physiological information is sometimes contradictory. For instance, the presence of Bacillus coagullans in hydrogen producing reactors has been associated to the increase of lactate production [24,25], but also to optimized hydrogen production [23,26].

The main possible reactions for the fermentation of arabinose and glucose, and the calculated Gibbs free energy of global reactions are shown in Table 3 (equations (3) to (10)) (only the reactions yielding experimentally detected soluble fermentation products in Rgluc and Rarab are represented). From a thermodynamic point of view, lactate formation from glucose and arabinose is less favorable than the formation of butyrate or ethanol. However, in continuous processes lactate was one of the main soluble fermentation products present in both reactors, especially in Rgluc at higher influent, substrate concentration (27.7 mM). This might be related to the need of recycling reducing power from NADH. It has been proposed that thermophiles usually possess some escape routes to dispose of reductants in order to prevent obstructions in their metabolic flux. A possible route for this is the production of more reduced organic compounds like lactate, acetone and butanol [9,23]. A switch to lactate formation in Thermoanaerobacterium sp. was observed as a mechanism of reductant disposal and NAD(P)H oxidation [9,27].

Hydrogen partial pressure and pH influence on hydrogen production yields

The metabolic pathways of hydrogen formation are sensitive to hydrogen concentrations and are subject to end-product inhibition. Results from this study showed that hydrogen production from arabinose and glucose is indeed higher when hydrogen is not allowed to accumulate in the headspace. Keeping low hydrogen partial pressure caused an increase in hydrogen production that could be mainly related to enhanced sugar utilization under these conditions. Nevertheless, in arabinose assays substrate was never completely depleted, not even when hydrogen was removed from the headspace. This can indicate that limiting factors other than PH2, such as liquid by-products inhibition, might be involved in hydrogen production from arabinose.

It has been reported that thermophilic hydrogen producing microorganisms could be inhibited by the presence of hydrogen, even when at very low partial pressure (from 0.1 × 104 to 7.5 × 104 Pa) [28]. Values of hydrogen partial pressure of 2 × 103 Pa, 1.6 × 103 Pa and 1.0 × 104 Pa were described as inhibitory for hydrogen production with Thermotoga maritima, Pyrococcus furiosus and Caldicellulosiruptor saccharolyticus, respectively [29]. In the present study hydrogen production by extreme thermophile mixed cultures using glucose and arabinose was inhibited at a PH2 similar to the one reported for C. saccharolyticus (that is, 1.2 × 104 Pa at 70°C).

Higher cumulative hydrogen production and yields were obtained at pH 7.0, either using glucose or arabinose as substrate. Lower hydrogen production at pH 5.5 was coupled to high ethanol and low acetate production (Figure 6). The present study suggests that, at extreme thermophilic conditions, maintenance of neutral pH (around 6.5 at 70°C) can aid preventing hydrogen losses by avoiding the production of more reduced organic compounds (such as lactic acid, acetone, butanol, and so on).

Overall, the results presented in this study show that both pH and hydrogen partial pressure affect hydrogen production efficiencies by extreme thermophilic mixed cultures. However, pH influenced hydrogen production in a greater extent than hydrogen partial pressure, both when using glucose or arabinose as substrate. Different soluble fermentation products' composition was observed in batch experiments and in continuous reactors. This can be related with the accumulation of soluble fermentation products happening in the batch assays, which can lead to different environmental conditions and, therefore, induce different metabolic pathways [30-32]. Nevertheless, batch results can give valuable insights for improving hydrogen production in continuous process.

Conclusions

In continuous reactor, hydrogen production rate from arabinose was significantly higher than from glucose, when using organic loading rates of 14 KgCOD m-3 d-1. This fact was associated with higher lactate production in the reactor fed with glucose, while in the arabinose-fed reactor, acetate and ethanol were the main end-products formed. The higher concentration of lactate was not a consequence of bacterial community shift, and is likely related to changes in the main metabolic pathways of glucose catabolism.

In batch mode, the effect of hydrogen partial pressure on hydrogen production from glucose was related to the extent of sugar utilization and not to the efficiency of substrate conversion to hydrogen. Furthermore, at pH 7.0, sugars uptake, hydrogen production and yield were higher than at pH 5.5, with both arabinose and glucose as substrates.

Methods

Continuous hydrogen production in EGSB reactors

Experiments were carried out in two plexi-glass EGSB reactors. An arabinose reactor (Rarab) and a glucose reactor (Rgluc) were fed with L-arabinose and glucose, respectively. EGSB reactors had a height of 1.95 m and internal diameter of 21 mm. Total liquid volume was 1.30 L, including reaction-zone volume of 0.7 L. Reactors were operated at 70 ± 1°C by means of an external water jacket, and pH inside the reactors was maintained at 5.5 ± 0.5. Superficial velocity was set at 10.0 m h-1 (using internal recirculation) with an hydraulic retention time (HRT) of 9 h. Before start-up, Rarab and Rgluc were inoculated with 400 mL of granular sludge from a lab-scale hydrogen-producing reactor that had been fed with a mixture of arabinose (17 mM) and glucose (14 mM) for two months. Start-up of Rarab was done using a constant arabinose feed concentration of 10.0 mM (period I); afterwards, arabinose concentrations of 16.6 mM (period II) and 33.3 mM (period III) were fed. Start-up of Rgluc was done using a constant glucose feed concentration of 8.3 mM (period I); afterwards, concentrations of 13.8 mM (period II) and 27.7 mM (period III) were tested (Table 4). Arabinose and glucose concentration differed in order to have identical theoretical hydrogen yields in both reactors (that is, 33.3, 55.5 and 110.8 mM H2 for periods I, II and III, respectively). Sodium bicarbonate was added to the feed as alkalinity source (at a final concentration of 1 to 2 g L-1). Macronutrients solution containing 30 g L-1MgSO4.7H2O, 28.3 g L-1 KH2PO4 and 170 g L-1) NH4Cl was also added (0.6 mL macronutrients solution per g of chemical oxygen demand (COD) in the feed).

Table 4. Operational conditions of glucose reactor (Rgluc) and arabinose reactor (Rarab)

Batch experiments

Seed sludge

Granular sludge used for inoculating batch assays for studying arabinose- and glucose-conversion was collected from reactors Rarab and Rgluc, respectively.

Medium composition and substrates

Assays were performed in 70 mL serum bottles containing 18 mL of buffered medium. Phosphate-buffered medium (20 mM) and bicarbonate-buffered medium (Stams et al. 1993) were used for experiments at pH 5.5 and pH 7, respectively. Bottles with phosphate-buffered medium were flushed with N2 (100%), while bottles with bicarbonate-buffered medium were equilibrated with a mixture of N2:CO2 (80:20%). Both media were supplemented with trace elements, salts and vitamins according to the procedure described by Stams et al. [33]; yeast extract was added to a final concentration of 0.5 g L-1. Medium was reduced with 0.8 mM sodium sulfide (Na2S.9H2O) and inoculated with 0.4 g of granular sludge. Arabinose (13 mM) and glucose (11 mM) were used as the main carbon source. Bottles were incubated in the dark at 70°C without shaking. After substrate depletion, a second pulse of 13 mM arabinose or 11 mM glucose was added and incubation extended.

Effect of hydrogen partial pressure

The effect of hydrogen partial pressure on hydrogen production from arabinose and glucose was investigated in batch mode at pH 5.5. Two series of batch experiments were performed: in series NHF (no headspace flushing), hydrogen was allowed to accumulate in the gas phase, while in series HF (headspace flushing) hydrogen was removed from the bottles' headspace and replaced by 100% N2. All experiments were performed in triplicate and included controls without substrate. Sugars consumption, production of hydrogen gas and soluble fermentation products were monitored. Dissolved hydrogen concentration was calculated using the Henry's law at 70°C: KH*Pi, where KH is the Henry's law constant for hydrogen (8.7 × 10-9 M/Pa at 70°C).

Effect of pH

The effect of pH on hydrogen production from arabinose and glucose fermentation was studied in two series of batch experiments, one at pH 7.0 and the other at pH 5.5. Incubation was done at 70°C and all the experiments were performed in triplicate. Sugars consumption, formation of hydrogen gas and soluble fermentation products were monitored and dissolved hydrogen concentration was calculated using the Henry's law at 70°C.

Analytical methods

Hydrogen concentration in the gas phase was determined by gas chromatography (GC) using a Hayesep Q column (80/100 mesh) and thermal conductivity detector Varian 3300 Gas Chromoatograph, (Varian, Walnut Creek, USA)) with nitrogen (30 mL minute-1) as the carrier gas. The injector, detector and column temperatures were 120, 170, and 35°C respectively. Methane and carbon dioxide content of the gas phase from batch experiments and EGSB reactors was determined by gas chromatography using a Porapack Q (100 to 180 mesh) column, with helium as the carrier gas at 30 mL minute-1, and a thermal conductivity detector. Temperatures of the detector, injector and oven were 110, 110 and 35°C, respectively. In the EGSB reactors gas flow rate was measured by a Ritter Milligascounter (Dr. Ing. Ritter Apparatebau GmbH, Bochum, Germany). Volatile fatty acids (VFA), ethanol, lactic acid, L-arabinose and glucose were determined by high performance liquid chromatography using an HPLC (Jasco, Tokyo, Japan) with a Chrompack column (6.5 × 30 mm2); sulfuric acid (0.01 N) at a flow rate of 0.7 mL minute-1 was used as mobile phase. Column temperature was set at 60°C. Detection of VFA, lactic acid, ethanol, arabinose, glucose was made sequentially using a UV detector at 210 nm and a RI detector.

PCR-DGGE

Representative granular sludge samples were collected from Rarab and Rgluc and stored at -18°C. Total genomic DNA was extracted from approximately 500 μL of sample by using the FastDNA SPIN kit for soil (Qbiogene, Carlsbad, CA, USA). 16S rRNA gene fragments of approximately 450 bp were amplified for DGGE analysis by PCR using a Taq DNA polymerase kit (Life Technologies, Gaithersburg, MD, USA) using the primer set 954GC-f and 1369-r, as previously described by Nubel et al. [34]. The size of the obtained PCR products was checked by comparison with appropriate size and mass standard (MBI Fermentas, Vilnius, Lithuania), by electrophoresis on an 1% (w/v) agarose gel and ethidium bromide staining. Gels ran at a constant voltage of 100 V in an agarose gel electrophoresis system (Mupid-EX, Seraing, Belgium). Nucleic acids were detected using an UV transilluminator (BioRad, Hercules, CA, USA).

DGGE analysis of the amplicons was done by using the DCode system (Bio-Rad). PCR products were electrophoresed in a 0.5 × Trisacetate-EDTA buffer for 16 h at 85 V and 60°C on polyacrylamide gel (8%) containing a linear gradient ranging from 30% to 60% denaturant. Silver staining of DGGE gels was performed as previously described [35]. DGGE gels were scanned at 400 dpi and the DGGE profiles compared using the Bionumerics 5.0 software package (Applied Maths, Gent, Belgium). Similarity indices (Si) of the compared profiles were calculated from the densitometric curves of the scanned DGGE profiles by using the Pearson product-moment correlation [36].

Gibb's Free energy calculations

Standard Gibb's free energy at 25°C (ΔGo) was calculated using standard Gibb's free energy of formation values (ΔGof) obtained from the literature [19,20] or calculated using the group addition method [19].

Abbreviations

DGGE: denaturing gradient gel electrophoresis; EGSB: expanded granular sludge bed; NADH: reduced form of nicotinamide adenine dinucleotide; PCR: polymerase chain reaction; PH2 : hydrogen partial pressure.

Competing interests

The authors declare that they have no competing interests.

Authors' contributions

All authors contributed intellectually via scientific discussions during the work and have read and approved the final manuscript. AAA designed the study, executed the experimental work, data interpretation and drafted the manuscript. IA and DK commented on the manuscript and contributed to the design of the study. DZS participated in data interpretation, reaction thermodynamics calculations and reviewed the manuscript. MMA contributed to the design of the study, data interpretation and reviewed the manuscript. All authors read and approved the final manuscript.

Acknowledgements

The financial support from Fundação para a Ciência e Tecnologia (FCT) through the PhD grant SFRH/BD/29823/2006 given to Abreu is gratefully acknowledged. This study also received support from Danish Agency for Science, Technology and Innovation under Bio REF. Project No. 2104-06-0004.

References

  1. Ren Nanqi, Guo Wanqian, Liu Bingfeng, Cao Gauangli, Ding Jie: Biological hydrogen production by dark fermentation: challenges and prospects towards scaled-up production.

    Curr Opin Biotechnol 2011, 22:365-370. PubMed Abstract | Publisher Full Text OpenURL

  2. Wang JL, Wan W: Factors influencing fermentative hydrogen production: A review.

    Int J Hydrogen Energy 2009, 34:799-811. Publisher Full Text OpenURL

  3. Chieh-Lun Cheng, Yung-Chung Lo, Kuo-Shing Lee, Duu-Jong Lee, Chiu-Yue Lin, Jo-Shu Chang: Biohydrogen production from lignocellulosic feedstock.

    Bioresour Technol 2011, 102:8514-8523. PubMed Abstract | Publisher Full Text OpenURL

  4. Xia LM, Sheng XL: High yield cellulase production by Trichoderma reesei ZU-02 on corncob residues.

    Bioresour Technol 2004, 91:259-262. PubMed Abstract | Publisher Full Text OpenURL

  5. Strobel HJ: Evidence for catabolite inhibition in regulation of pentose utilization and transport in the ruminal bacterium selenomonas-ruminantium.

    Appl Environ Microbiol 1993, 59:40-46. PubMed Abstract | Publisher Full Text | PubMed Central Full Text OpenURL

  6. Abreu AA, Alves JI, Pereira MA, Karakashev D, Alves MM, Angelidaki I: Engineered heat treated methanogenic granules: a promising biotechnological approach for extreme thermophilic biohydrogen production.

    Bioresour Technol 2010, 101:9577-9586. PubMed Abstract | Publisher Full Text OpenURL

  7. Jones DT, Woods DR: Acetone-butanol fermentation revisited.

    Microbiol Rev 1986, 50:484-524. PubMed Abstract | Publisher Full Text | PubMed Central Full Text OpenURL

  8. Turcot J, Bisaillon A, Hallenbeck PC: Hydrogen production by continuous cultures of Escherchia coli under different nutrient regimes.

    Int J Hydrogen Energy 2008, 33:1465-1470. Publisher Full Text OpenURL

  9. Verhaart MRA, Bielen AAM, van der Oost J, Stams AJM, Kengen SWM: Hydrogen production by hyperthermophilic and extremely thermophilic bacteria and archaea: mechanisms for reductant disposal.

    Environ Technol 2010, 31:993-1003. PubMed Abstract | Publisher Full Text OpenURL

  10. Valdez-Vazquez I, Poggi-Varaldo HM: Hydrogen production by fermentative consortia.

    Renew Sustain Energy Rev 2011, 13:1000-1013. OpenURL

  11. Stams AJM: Metabolic interactions between anaerobic-bacteria in methanogenic environments.

    Antonie Van Leeuwenhoek 1994, 66:271-294. PubMed Abstract | Publisher Full Text OpenURL

  12. Hawkes FR, Dinsdale R, Hawkes DL, Hussy I: Sustainable fermentative hydrogen production: challenges for process optimisation.

    Int J Hydrogen Energy 2002, 27:1339-1347. Publisher Full Text OpenURL

  13. van Groenestijn JW, Hazewinkel JHO, Nienoord M, Bussmann PJT: Energy aspects of biological hydrogen production in high rate bioreactors operated in the thermophilic temperature range.

    Int J Hydrogen Energy 2002, 27:1141-1147. Publisher Full Text OpenURL

  14. Lu JQ, Gavala HN, Skiadas IV, Mladenovska Z, Ahring BK: Improving anaerobic sewage sludge digestion by implementation of a hyper-thermophilic prehydrolysis step.

    J Environ Manage 2008, 88:881-889. PubMed Abstract | Publisher Full Text OpenURL

  15. Kleerebezem R, van Loosdrecht MCM: Mixed culture biotechnology for bioenergy production.

    Curr Opin Biotechnol 2007, 18:207-212. PubMed Abstract | Publisher Full Text OpenURL

  16. Temudo MF, Kleerebezem R, van Loosdrecht M: Influence of the pH on (open) mixed culture fermentation of glucose: a chemostat study.

    Biotechnol Bioeng 2007, 98:69-79. PubMed Abstract | Publisher Full Text OpenURL

  17. Nanqi Ren, Aijie Wang, Guangli Cao, Jifei Xu, Lingfang Gao: Bioconversion of lignocellulosic biomass to hydrogen: potential and challenges.

    Biotechnol Adv 2009, 27:1051-1060. PubMed Abstract | Publisher Full Text OpenURL

  18. Willquist K, Zeidan AA, van Niel EWJ: Physiological characteristics of the extreme thermophile Caldicellulosiruptor saccharolyticus: an efficient hydrogen cell factory.

    Microb Cell Fac 2010, 9:89. BioMed Central Full Text OpenURL

  19. Mavrovouniotis ML: Estimation of standard Gibbs energy changes of biotransformations.

    J Biol Chem 1991, 266:14440-14445. PubMed Abstract | Publisher Full Text OpenURL

  20. Thauer RK, Jungermann K, Decker K: Energy-Conservation in Chemotropic Anaerobic Bacteria.

    Bacteriol Rev 1977, 41:100-180. PubMed Abstract | Publisher Full Text | PubMed Central Full Text OpenURL

  21. Altaras NE, Etzel MR, Cameron DC: Conversion of sugars to 1,2-propanediol by Thermoanaerobacterium thermosaccharolyticum HG-8.

    Biotechnol Prog 2001, 17:52-56. PubMed Abstract | Publisher Full Text OpenURL

  22. Wu KJ, Saratale GD, Lo YC, Chen WM, Tseng ZJ, Chang MC, Tsai BC, Su A, Chang JS: Simultaneous production of 2,3-butanediol, ethanol and hydrogen with a Klebsiella sp strain isolated from sewage sludge.

    Bioresour Technol 2008, 99:7966-7970. PubMed Abstract | Publisher Full Text OpenURL

  23. Kotay SM, Das D: Microbial hydrogen production with Bacillus coagulans IIT-BT S1 isolated from anaerobic sewage sludge.

    Bioresour Technol 2007, 98:1183-1190. PubMed Abstract | Publisher Full Text OpenURL

  24. Karadag D, Puhakka JA: Direction of glucose fermentation towards hydrogen or ethanol production through on-line pH control.

    Int J Hydrogen Energy 2010, 35:10245-10251. Publisher Full Text OpenURL

  25. Karadag D, Puhakka JA: Effect of changing temperature on anaerobic hydrogen production and microbial community composition in an open-mixed culture bioreactor.

    Int J Hydrogen Energy 2010, 35:10954-10959. Publisher Full Text OpenURL

  26. Kotay SM, Das D: Microbial hydrogen production from sewage sludge bioaugmented with a constructed microbial consortium.

    Int J Hydrogen Energy 2010, 35:10653-10659. Publisher Full Text OpenURL

  27. Shaw AJ, Hogsett DA, Lynd LR: Identification of the [FeFe]-hydrogenase responsible for hydrogen generation in Thermoanaerobacterium saccharolyticum and demonstration of increased ethanol yield via hydrogenase knockout.

    J Bacteriol 2009, 191:6457-6464. PubMed Abstract | Publisher Full Text | PubMed Central Full Text OpenURL

  28. Kengen SWM, Stams AJM, deVos WM: Sugar metabolism of hyperthermophiles.

    FEMS Microbiol Rev 1996, 18:119-137. Publisher Full Text OpenURL

  29. Adams MWW: The metabolism of hydrogen by extremely thermophilic, sulfur-dependent bacteria.

    FEMS Microbiol Rev 1990, 75:219-237. Publisher Full Text OpenURL

  30. van Niel EWJ, Claassen PAM, Stams AJM: Substrate and product inhibition of hydrogen production by the extreme thermophile, Caldicellulosiruptor saccharolyticus.

    Biotechnol Bioeng 2003, 81:255-262. PubMed Abstract | Publisher Full Text OpenURL

  31. Schafer T, Schonheit P: Pyruvate metabolism of the hyperthermophilic Archaebacterium pyrococcus-furiosus - acetate formation from acetyl-coa and Atp synthesis are catalyzed by an acetyl-coa synthetase (Adp forming).

    Arch Microbiol 1991, 155:366-377. OpenURL

  32. Schroder C, Selig M, Schonheit P: Glucose fermentation to acetate, co2 and h-2 in the anaerobic hyperthermophilic Eubacterium thermotoga-maritima - involvement of the Embden-Meyerhof Pathway.

    Arch Microbiol 1994, 161:460-470. OpenURL

  33. Stams AJM, Vandijk JB, Dijkema C, Plugge CM: Growth of syntrophic propionate-oxidizing bacteria with fumarate in the absence of methanogenic bacteria.

    Appl Environ Microbiol 1993, 59:1114-1119. PubMed Abstract | Publisher Full Text | PubMed Central Full Text OpenURL

  34. Nubel U, Engelen B, Felske A, Snaidr J, Wieshuber A, Amann RI, Ludwig W, Backhaus H: Sequence heterogeneities of genes encoding 16S rRNAs in Paenibacillus polymyxa detected by temperature gradient gel electrophoresis.

    J Bacteriol 1996, 178:5636-5643. PubMed Abstract | Publisher Full Text | PubMed Central Full Text OpenURL

  35. Sanguinetti CJ, Neto ED, Simpson AJG: Rapid silver staining and recovery of pcr products separated on polyacrylamide gels.

    Biotechniques 1994, 17:914-. PubMed Abstract OpenURL

  36. Hane BG, Jager K, Drexler HG: The Pearson Product-Moment Correlation-Coefficient Is better suited for identification of DNA fingerprint profiles than band matching algorithms.

    Electrophoresis 1993, 14:967-972. PubMed Abstract | Publisher Full Text OpenURL